Cub Cadet 2000 Series Manuel de l'opérateur

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOperatOr’s ManualSafe Operation Practices • Set-Up • Operation • Maintenance •

10 Section 2 — ASSembly & Set-UpChecking Tire PressureWARNING! Maximum tire pressure under any 

Controls & Features411Hour Meter/Service IndicatorCruise Control/Parking Brake LeverBrake PedalCup HolderStorage CompartmentFuel CapPTO/Blade Enga

12 Section 4 — controlS & FeatureSForward Drive PedalThe forward drive pedal is located on the right side of the tractor, along the running board.

13Section 4 — controlS & FeatureSLow Gas WindowThe low gas window is located at the rear of the tractor. If the gas level is visible in this windo

Operation5WARNING! Avoid serious injury or death. Go up and down slopes, not across. Avoid sudden turns. Do not operate unit where it could slip or ti

Section 5 — operationReverse Caution Mode position of the key switch module allows the tractor to be operated in reverse wit

Section 5 — operationDriving On Slopeswhere you may operate the tractor safely.WARNING! Do

Section 5 — operationOperating the Headlights 

Maintenance & Adjustments6NOTE: features may vary by model. Not all features in this manual

Section 6 — Maintenance & adjuStMentSHydrostatic Transmission OilChecking the Hydrostatic Transmission OilThe dipstick to check the hydrostatic tr

To The Owner12Safe Operation Practices ... 3Assembly & Set-Up ...

Section 6 — Maintenance & adjuStMentS Remove the drain plug and allow the transmission oil to drain into a clean container having a capacity of

Section 6 — Maintenance & adjuStMentSSteering Housing & Steering ShaftThe steering housing and steering shaft should be lubricated after every

Section 6 — Maintenance & adjuStMentS5. Loosen the jam nuts from the ball joints. See Figure 6-7.Ball JointDrag LinkHex Lock NutJam NutSteering

Section 6 — Maintenance & adjuStMentSLift Handle Adjustment (If so equipped)The effort required to operate the implement lift handle can be varied

Se rvi ce724 Note which battery tray hole the RH side of the hold-down rod is hooked into.4. Rotate the hold-down rod upward, over and around the

25Section 7 — ServiceHeadlights Refer to Replacement Parts section when replacement of head lamp bulbs is necessary.Replace headlight bulbs as follows

Troubleshooting826Problem Cause RemedyExcessive vibration  Cutting blade loose or unbalanced. 2. Damaged or bent cutting blade.  Tighten blade

Replacement Parts927Component Part Number and Description  946-04759A Choke Control Cable 

Attachments & Accessories1028The following attachments and accessories are compatible for 

No tes1129

Important Safe Operation Practices23General Operation Read, understand, and follow all instructions on the machine and in the manual(s) before atte

FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSMTD Consumer Group Inc, the United States Environmen

GDOC-100223 Rev. A Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on o

original proof of purchase and applicable maintenance records to the 

4 Section 2 — important Safe operation practiceS A missing or damaged discharge cover can cause blade contact or thrown object injuries.  Stop

5Section 2 — important Safe operation practiceSChildren Tragic accidents can occur if the operator is not alert to the presence of children. Childr

6 Section 2 — important Safe operation practiceS Periodically check to make sure the blades come to complete stop within approximately (5) five sec

7Section 2 — important Safe operation practiceSSafety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, un

8 Section 2 — important Safe operation practiceS(OK) (TOO STEEP)USE THIS SLOPE GAUGE TO DETERMINEIF A SLOPE IS TOO STEEP FOR SAFE OPERATION!To check t

Assembly & Set-Up39NOTE: features may vary by model. Not all features in this manual are app