Cub-cadet 20HP Z-Force 44 Manuel d'utilisateur télécharger pdf (Page 7)

cases should not be punctured. Lead is poisonous

and is contained within the

positive and negative ter-

minals as well as within the battery’s internal grid-

work of plates and active materials.

A. Explosive gases are generated when batteries

are re-charged, so sparks, flames and heat sources

should be avoided. Loose connections at the battery

terminals can produce sparks and heat...connections

to the terminals must be kept tight, and the terminals

and battery surfaces kept clean of acids and corro

sion. If batteries are re-charged or “jumped” from

external sources, make sure that the connections are

made properly and in the correct sequence...connect

to the positive terminal of the good battery first, then

connect that to the positive terminal of the weak bat

tery. The third connection should be to the negative

terminal of the good battery, followed by the negative

terminal of the weak battery. If sparks are observed

or heating of the wiring or connectors is detected,

disconnect in reverse order (I.E., the negative termi

nal of the weak battery first). Batteries should be re-

charged at a constant voltage...generally 14.5 +/- 0.5

volts DC for a nominal 12 volt DC battery.

F. Related to Fuel

1. Fuel is highly flammable and its vapors can

explode if ignited. Please respect it.

2. Do not smoke or permit others to smoke

while handling fuel.

3. Always use approved containers for fuel and

fill slowly to decrease the chance of static

electricity buildup and spillage.

4. Store fuel in well ventilated and unoccupied

buildings away from sparks and flames.

5. When dispensing gasoline into approved con-

tainers, place the container on the ground

when refueling to avoid a possible static elec

tricity ignition of fuel vapors.

6. Do not fill containers while it is inside a vehi-

cle, trunk, the bed of a pickup or floor of a

trailer.

7. Always shut off the engine and permit it to

cool before removing the fuel tank cap.

8. Always fill the fuel tank outdoors.

9. If the fuel container spout will not fit inside the

fuel tank opening, use a funnel.

10. When filling the fuel tank, stop when the fuel

reaches one inch from the top. This space is

necessary for tank expansion.

Do not overfill

11. Wipe up any spilled fuel

G. Towing

1. Tow only with a machine that has an

approved hitch designed for towing. Do not

attach towed equipment except at the hitch

point.

2. Follow the manufacturers recommendation for

weight limits for towed equipment and towing

on slopes.

3. Never allow children or others in or on towed

equipment.

4. On slopes, the weight of the towed equipment

may cause loss of traction and loss of control.

Note: 5 degrees (9%) maximum slope.

5. Travel slowly and allow extra distance to stop.

H. Suspension - Gel

1. This unit is equipped with a one-piece seat

back, seat bottom and foldable armrests.

The seat bottom and seat back are covered

with Spray Skin Technology (SST) that pro

vides a seamless and waterproof covering.

The seat backs and seat bottoms are

attached to a one piece molded plastic shell

that eliminates metal frames while reducing

weight. An OPS in the form of a switch, is

integrated into the seat bottom and is con

nected to the machine electrical system.

2. This unit is equipped with a unique gel sus-

pension means incorporating Sorbothane.

Sorbothane is a highly damped, visco-elas

tic, polymeric solid that flows like liquid under

load. It is a thermoset, polyether-based poly

urethane that combines high-energy absorp-

tion with near faultless memory to

simultaneously absorb shock and vibration

energy. This means that it reacts like a com

bination of springs and dampers.

3. The fore/aft single-locking adjustment tracks

operate on roller-bearings for smooth and

almost effortless operation. The lever for seat

track actuation is near the right front corner

of the seat bottom, and allows fore/aft adjust

ment of 4”.

4. The seat is attached to pivotal brackets,

which allow the seat assembly to pivot for

ward onto the foot platform area.

Note: The Operator Presence Sensor must be con-

nected to the electrical wiring harness

WARNING-YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who

read, understand and follow the warnings and instructions in this manual and on the machine.

1 2 3 4 5 6 7 8 9 10 11 12 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Cub-cadet 20HP Z-Force 44 Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Cub-cadet 20HP Z-Force 44