Cub Cadet CS 2210 Manuel d'utilisateur télécharger pdf (Page 11)

11se c t i O n 5 — Op e r a t i O n

Chipping

Never operate the chipper shredder

without chipper chute lowered into the operating

position.

Branches up to two inches (model series CS 2210) or three

inches (model series CS 3210) in diameter can be fed into the

chipper chute. Observe the following guidelines when chipping

branches:

Keep both hands firmly on the branch as you feed it into •

the chipper chute.

Never feed more than one branch into the chipper chute at •

a time.

Never feed anything other than branches (or wood) into •

the chipper chute.

Apply intermittent pressure (force, in short pulses) while •

feeding larger branches into the chipper chute, to avoid

bogging or stalling the engine.

IMPORTANT: Never feed branches with a diameter greater

than two (2) inches (Model Series CS 2210) or three (3)

inches (model series CS 3210) into the chipper chute. Doing

so can result in serious damage to your unit’s chipper

blades, flails or impeller.

NOTE: For best performance, always operate the unit with

sharp chipper blades. If a noticeable loss in performance is

encountered while chipping branches, the chipper blades

should be replaced.

Emptying the Bag

Stop engine.1.

Squeeze the locking buckle to release the bag’s drawstrap 2.

before loosening it from the chute deflector. See Fig. 5-3.

Empty the bag and reattach to the chute deflector 3.

opening. Refer to the “Set-Up & Adjustments” section of

this manual.

Shredding

Yard waste such as leaves and pine needles can be placed in

the hopper for shredding. After material has been processed by

the shredder blade and flails, it will be forced out of the chute

deflector, and, if attached, into a debris collection bag.

Observe the following guidelines when shredding yard debris:

Never attempt to shred material other than normal yard •

debris (leaves, twigs, pine cones, etc.).

Avoid shredding fibrous plants such as tomato vines until •

they are thoroughly dried out. Fresh vines do not shred

well and tend to wrap themselves around the impeller and

flails.

Place reasonable amounts of debris into the hopper at a •

time. Do not overload the hopper.

Allow the material in the hopper to be drawn into the •

blades and shredded before adding additional debris

to the hopper. Failure to due so may result in a clogged

hopper, clogged chute deflector or a stalled engine.

Avoid placing twigs longer than 24 inches into the hopper. •

Twigs longer than 24 inches may result in a clogged

hopper.

IMPORTANT: Never place branches with a diameter greater

than 1/2-inch in the hopper. Doing so can result in serious

damage to the unit’s shredder blade, flails or impeller.

Clearing the Hopper

Should the hopper become clogged with debris during

operation, proceed as follows:

Grasp the handle with both hands and gently agitate the 1.

chipper shredder to help loosen debris, drawing it into the

impeller.

If the clog does not clear, proceed as follows:

Stop engine.1.

Use your hands to remove any debris found near the top of 2.

the hopper.

Use a branch (or other available device, i.e. broomstick) to 3.

dislodge debris located toward the base of the hopper.

Restart engine.4.

NOTE: If you’re unable to pull the starter rope as a result of

accumulated debris near the impeller, follow instructions

under the heading Cleaning the Reduction Chamber in the

“Maintainenance & Adjustments” section of this manual.



1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 39 40

Commentaires sur ces manuels

Pas de commentaire

Cub Cadet CS 2210 Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Broyeurs pour jardin Cub Cadet CS 2210