Cub-cadet CLT-160 Manuel d'utilisateur télécharger pdf (Page 13)

SYSTEMS INDICATOR MONITOR / HOUR

METER

Your tractor is equipped with either an hour meter or an

ammeter as part of two available system indicator

monitors. Locate the monitor on the left side of your

dash panel and compare it to both shown in Figure 10.

Figure 10

If the Brake light or PTO light illuminates when

attempting to start the unit, proceed as follows:

Brake — Engage the parking brake.

PTO — Move the PTO lever into the disengaged

(OFF) position.

It is normal for the Oil light and the Battery light to

illuminate while the engine is cranking, but if either

illuminates while the engine is running, proceed as

follows:

Oil— Stop the tractor immediately and check the

crankcase oil level as instructed in the

Engine Owner’s Manual included with

your unit. Add oil as required.

Battery— If this light illuminate’s while the engine is

running, it indicates that the battery is in

need of a charge OR that the engine’s

charging system is not generating

sufficient amperage. Refer to the

MAINTENANCE section of this manual

for the proper battery charging procedure

or have the engine’s charging system

checked by a authorized dealer.

On units so equipped, the ammeter measures the

electrical output of the engine’s charging system. Under

normal operating conditions, with the engine at full

throttle, the ammeter’s needle should measure a

positive charge.

The hour meter, on units so equipped, operates

whenever the engine is running and records the actual

hours of tractor operation.

ELECTRIC PTO (POWER

TAKE-OFF) KNOB

To engage the power to the

cutting deck or other (separately

available) attachments on models

so equipped with an electric PTO,

pull outward on the PTO knob.

Push the PTO knob inward to

disengage the power to the cutting deck.

NOTE: The PTO knob must be in the disengaged

(OFF) position when starting the engine, when

simultaneously moving both control handles into the

REVERSE position and if the operator leaves the seat.

PTO (POWER TAKE-OFF) LEVER

On models equipped with a manual PTO, the PTO lever

is located on the left side of the dashboard next to the

steering wheel. To engage the PTO, proceed as

follows:

1. Move the throttle control lever to the Fast (rabbit)

position.

2. Grasp the PTO (Blade Engage) lever and pivot it all

the way forward into the engaged (ON) position.

3. Keep the throttle lever in the Fast (rabbit) position

for the most efficient use of the cutting deck or other

(separately available) attachments.

4. To disengage the PTO, move the lever towards the

rear. This will cut off power to the deck and other

attachments.

NOTE: The PTO lever must be in the disengaged

(OFF) position when starting the engine, when traveling

in reverse and if the operator leaves the seat.

SEAT ADJUSTMENT LEVER

To adjust the seat forward or backward on units

equipped with a quick-adjust seat, slide the seat

adjustment lever to the left and reposition the seat to the

desired position. Once a comfortable position is found,

release the seat adjustment lever to lock the seat in

place. Refer to SEAT ADJUSTMENTS in the MAKING

ADJUSTMENTS section of this manual for more

detailed instructions.

DECK LIFT LEVER

Found on your tractor’s right fender, the deck lift lever is

used to change the height of the cutting deck. To use,

move the lever to the left, then place in the notch best

suited for your application.

Oil

Brake

PTO

AMPS

Ammeter

1/10

Battery

PTO

Oil

Brake

Hour Meter

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 28 29

Commentaires sur ces manuels

Pas de commentaire

Cub-cadet CLT-160 Manuel d'utilisateur Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Machines spéciales Cub-cadet CLT-160