Cub-cadet CLT-538 Manuel d'utilisateur télécharger pdf (Page 14)

NOTE: The parking brake must be set if the operator

leaves the seat with the engine running or the engine

will automatically shut off.

Setting the Cutting Height

Select the height position of the cutting deck by placing

the deck lift lever in any of the five different cutting

height notches on the right side of the fender. Then

adjust the deck wheels, if so equipped, so that they are

between ¼-inch and ½-inch above the ground when the

tractor is on a smooth, flat surface such as a driveway.

WARNING: Keep hands and feet away

from the discharge opening of the cutting

deck.

NOTE: On models so equipped, the deck wheels are

an anti-scalp feature of the deck and are not designed

to support the weight of the cutting deck.

Refer to Making Adjustments this manual for more detailed

instructions regarding various deck adjustments.

Starting the Engine

WARNING: Do not operate the tractor if the

interlock system is malfunctioning. This

system was designed for your safety and

protection.

NOTE: Refer to the TRACTOR SET-UP on page 8 of this

manual for Gasoline and Oil fill-up instructions.

• Insert the tractor key into the ignition switch.

• Place the PTO (Blade Engage) knob (or lever) in

the disengaged (OFF) position.

• Engage the tractor’s parking brake.

• Activate the choke control.

• Turn the ignition key clockwise to the START

position. After the engine starts, release the key. It

will return to the ON position.

IMPORTANT:

Do NOT hold the key in the START

position for longer than ten seconds at a time. Doing so

may cause damage to your engine’s electric starter.

• After the engine starts, deactivate the choke control

and place the throttle control in the FAST position.

NOTE: Do NOT leave the throttle control in the

CHOKE position while operating the tractor. Doing so

will result in a "rich" fuel mixture and cause the engine

to run poorly.

Stopping the Engine

WARNING: If you strike a foreign object,

stop the engine, disconnect the spark plug

wire(s) and ground against the engine.

Thoroughly inspect the machine for any

damage. Repair the damage before restarting

and operating

• If the blades are engaged, place the PTO (Blade

Engage) knob (or lever) in the disengaged (OFF)

position.

• Turn the ignition key counterclockwise to the OFF

position.

• Remove the key from the ignition switch to prevent

unintended starting.

Driving the Tractor

WARNING: Avoid sudden starts, ex-

cessive speed and sudden stops.

WARNING: Do not leave the seat of the

tractor without first placing the PTO (Blade

Engage) lever in the disengaged (OFF)

position, depressing the brake pedal and

engaging the parking brake. If leaving the

tractor unattended, also turn the ignition key

off and remove the key.

WARNING: Always look down and behind

before and while backing up to avoid a back-

over accident.

• Depress the brake pedal to release the parking

brake and let the pedal up.

• Move the throttle lever into the FAST (rabbit)

position.

• Place the shift lever in either the FORWARD or

REVERSE position.

IMPORTANT:

Do NOT use the shift lever to change the

direction of travel when the tractor is in motion. Always

use the brake pedal to bring the tractor to a complete

stop before shifting.

• Release the parking brake by depressing the

clutch-brake pedal and positioning the speed

control lever in desired position.

IMPORTANT:

First-time operators should use speed

positions 1 or 2. Become completely familiar with the

tractor’s operation and controls before operating the

tractor in higher speed positions.

• Release clutch-brake pedal slowly to put unit into

motion.

• The lawn tractor is brought to a stop by depressing

the clutch-brake pedal.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 67 68

Commentaires sur ces manuels

Pas de commentaire

Cub-cadet CLT-538 Manuel d'utilisateur Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Machines spéciales Cub-cadet CLT-538