Cub Cadet CS 202 Manuel de l'opérateur télécharger pdf (Page 1)

769-07498 P01 03/12

IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.

Removing Unit From Carton

Assemble The Unit

Starting The Unit

Slide shield’s slot onto

mounting bracket. Rotate

shield onto shaft. Push

square bolt through shield

and bracket. Tighten

washer and wing nut

onto bolt.

Remove the protective cap

and gray spacer from the

upper and lower shafts.

Push the attachment into

the coupler. Turn the knob

clockwise to tighten.

Assemble The Unit

Mix thoroughly in a separate

fuel can:

– 3.2 fl. oz. of 2-cycle

engine oil

– 1 gallon of unleaded

gasoline

NOTE: Do not mix directly in

the unit fuel tank.

Place unit on a level surface.

Fill fuel tank.

Press primer bulb 10 times,

or until fuel is visible

Crouch in starting position. SQUEEZE and HOLD

throttle for ALL further

steps.

Pull rope 5 times. Move choke lever to

Position 2 and squeeze

throttle.

Pull rope 3-5 times to start

engine. Run unit for 30-60

seconds to warm up.

Continue to squeeze

throttle. Move choke lever

to Position 3.

11 2

Remove all contents from

carton.

5 6 7

19 10

Loosen the bolt. Move the

handle to the location that

provides the best grip. Move

the handle a minimum of 6

inches away from the shaft

grip. Tighten the bolt until the

handle is secure.

Move choke lever to

Position 1.

Continue to squeeze

throttle. Run unit for an

additional 60 seconds to

complete warm-up. Unit

may be used during this

time.

Starting The Unit

Primer

Bulb

10 X

5 X

3-5 X

Choke Lever

Starter Rope

Fuel Cap

Throttle Control

On/ Off Switch

D-Handle

Rapid-link™

Cutting Head Shield

Need Help?

Call 1-877-282-8684

Choke Lever

Slot

Bracket

Min. 6”

ASSEMBLY TOOLS REQUIRED:

• 3/8” Socket

40:1

Knob

DIDN’T START?

Repeat the starting instructions.

If the unit still fails to start,

refer to the operator’s manual

for additional starting and

troubleshooting information.

Bump

Knob

Inner

Reel

Outer

Spool

Spring

Top Hole

Bottom Hole

Split Wall

Unscrew the bump knob

counterclockwise.

Remove the inner reel and

spring.

Cut one 6-foot (1.8 m)

length of new 0.095” split

line trimming line. Split each

end about 6 inches (150

mm).

Insert the end of one line

into the top hole and the

end of the other line into the

bottom hole.

Wind the line tightly in the

direction shown on the inner

reel. The split wall will divide

the line. Wind the line until it

is completely divided and

about 6 inches (150 mm) of

line remains.

Insert the two 6-inch

sections into the two .095

holding slots.

11 2

Pass the two line ends

through the eyelets. Place

the spring inside the inner

reel. Insert the inner reel into

the outer spool. Push the

inner reel and outer spool

together.

Reloading The Line*

Hold the inner reel and outer

spool together. Firmly pull

the two line ends to release

them from the holding slots.

Screw the bump knob on

clockwise. Tighten the bump

knob securely.

Reloading The Line

Holding Slots

Eyelets

For replacement line, call 1-877-282-8684 or go to

an authorized service dealer.

For single line installation or replacement spool

installation instructions, refer to the Replacing the

Trimming Line section of this manual.

*This is to assist in the reloading of Splitline® only. These instructions

are NOT part of the fast assembly instructions. Line does not need to

be installed on the initial assembly and start-up.

Español — Page 11 English — Page 1Français — Page 6

NEED HELP? CALL 1-877-282-8684 IN U.S. OR 1-800-668-1238 IN CANADA

CS202

2-Cycle Trimmer

Operator’s Manual

1 2 3 4 5 6 ... 15 16

Résumé du contenu

Page 1 - Operator’s Manual

769-07498 P01 03/12IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.Removing Unit Fro

Page 2 - SAVE THESE INSTRUCTIONS

PROBLÈME SOLUTIONLa protection de survitesse de moteur s'est engagéePermettez au moteur de refroidir pendant 10 minutesavant le recommencement.Le

Page 3

769-07498 P01 03/12IMPORTANTE: LEA BIEN EL MANUAL DEL OPERADOR Y, AL OPERAR LA UNIDAD, SIGA LAS INSTRUCCIONES PARA EL FUNCIONAMIENTO SEGURO.Sacar la u

Page 4 - Choke Lever

• Mezcle o eche siempre el combustible en un área exterior bien ventilada y limpia, donde no haya chispas ni llamas.NO fume.• No opere nunca la unidad

Page 5 - TROUBLESHOOTING

Rapid-link™ CONOZCA SU UNIDADGatillo delreguladorManija en DManjodel ejeCubierta delfiltro de aireBujía de encendidoBastidor del ejeMango de la cuerda

Page 6 - Manuel de L'utilisateur

OPERACIÓNMANTENIMIENTOPLAN DE MANTENIMIENTOLleve a cabo los procedimientos necesarios de mantenimiento con la frecuencia indicada en la tabla. Estospr

Page 7 - CONSERVEZ CES INSTRUCTIONS

PROBLEMA SOLUCIÓNEl filtro de aire está sucio Limpie o cambie el filtro de aireEl combustible está viejo (tiene más de 30 días) y/o malmezcladoVacíe e

Page 8

The limited warranty set forth below is given by Cub Cadet LLC (“Cub Cadet”) with respect with new merchandise purchased and used in the United States

Page 9

2• SAFETY & INTERNATIONAL SYMBOLS •This operator's manual describes safety and international symbols and pictographs that may appear on this

Page 10 - Languette de

INSTALLING THE CUTTING HEAD SHIELDUse the following instructions if the cutting head shield is not installed. Use only theinstructions that apply to t

Page 11 - Manual del Operador

LINE INSTALLATIONOnly use the trimming line described in the Specifications section. Other types oftrimming line may cause the engine to overheat or f

Page 12 - CONSERVE ESTAS INSTRUCCIONES

PROBLEM SOLUTIONEngine overspeed protection engagedAllow the engine to cool down for 10 minutes beforerestarting.5MAINTENANCEThe fuel is old (over 30

Page 13

769-07498 P01 03/12IMPORTANT : LISEZ ATTENTIVEMENT LE MANUEL DE L’UTILISATEUR ET CONFORMEZ-VOUS AUX INSTRUCTIONS POUR UNE UTILISATIONDE L’APPAREIL EN

Page 14

7• SYMBOLES INTERNATIONAUX ET DE SÉCURITÉ •Ce manuel de l’utilisateur décrit les symboles et pictogrammes de sécurité internationaux qui peuventappara

Page 15 - Lengüeta

Rapid-link™ INSTALLATION ET AJUSTEMENT DE LA POIGNÉE EN D Installation de la poignée en D1. Poussez la poignée en D vers le bas sur la rallonge (Fig.

Page 16 - CUB CADET LLC

UTILISATIONPROGRAMME D’ENTRETIENEffectuez ces procédures d’entretien obligatoires aux fréquences indiquées dans le tableau d’entretien. Cesprocédures

Commentaires sur ces manuels

Pas de commentaire

Cub Cadet CS 202 Manuel de l'opérateur Page 1

Naviguer en ligne ou télécharger Manuel de l'opérateur pour Outils de jardin Cub Cadet CS 202. Cub Cadet CS 202 Operator`s manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Cub Cadet CS 202 Manuel de l'opérateur Page 1

Naviguer en ligne ou télécharger Manuel de l'opérateur pour Outils de jardin Cub Cadet CS 202. Cub Cadet CS 202 Operator`s manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils de jardin Cub Cadet CS 202